Anti Slip Plastic Ground Protection Mats are reusable HDPE and UHMWPE panels designed for temporary pedestrian, vehicle, and equipment access across mud, grass, soft soil, wet ground, and other outdoor surfaces.
Extruded sizes include options such as 1220 × 2440 mm, 910 × 2440 mm, and 610 × 2440 mm, with thicknesses of 12.7 mm, 15 mm, 18 mm, and 20 mm. Larger molded road mats are available in sizes up to approximately 4500 × 2000 mm, with selected thickness ranges from approximately 30 to 100 mm.
The panels feature raised anti-slip patterns with a reference cleat height of approximately 7 mm, integrated handling holes, low moisture absorption, reusable construction, and multiple color options.
Anti Slip Plastic Ground Protection Mats are reusable access panels designed to create temporary pedestrian, vehicle, and equipment routes across muddy roads, grass, soft soil, wet surfaces, landscaped areas, and other outdoor ground conditions. Available in HDPE and UHMWPE material options, these plastic mats combine raised traction surfaces, low moisture absorption, practical impact resistance, reusable performance, and a wide selection of panel dimensions.
The product range includes both extruded road mats and molded HDPE road mats. Common extruded dimensions include 1220 × 2440 mm, 910 × 2440 mm, 610 × 2440 mm, 910 × 1830 mm, 610 × 1830 mm, 610 × 1220 mm, 1100 × 2440 mm, 1100 × 2900 mm, 1000 × 2440 mm, and 1000 × 1900 mm.
Reference extruded panel thicknesses include 12.7 mm, 15 mm, 18 mm, and 20 mm. Larger molded road mats are available in dimensions such as 2500 × 1300 mm, 2300 × 1200 mm, 3000 × 1020 mm, 3000 × 1500 mm, 2000 × 1000 mm, and 4500 × 2000 mm. Depending on the selected molded model, thickness ranges from approximately 30 mm to 100 mm.
The surface can be produced with raised patterns on both sides or with a patterned side and a smoother opposite side. The referenced cleat height is approximately 7 mm, helping create a more defined contact surface for vehicle tires and footwear.
Actual product performance depends on material type, panel dimensions, thickness, supporting ground, vehicle axle load, tire or track contact area, traffic frequency, turning movement, braking forces, installation layout, and the operating environment.
The following specifications are based on the supplied product information:
The wide range of panel dimensions allows Anti Slip Plastic Ground Protection Mats to be selected according to the required route width, traffic type, vehicle dimensions, working area, transportation requirements, and supporting ground.
The extruded product range includes multiple standard dimensions suitable for temporary access and ground protection.
The 1220 × 2440 mm panel is approximately equivalent to a 4 × 8 ft format. It is one of the most practical sizes for modular temporary access routes and provides approximately 2.98 square metres of gross surface coverage.
The 910 × 2440 mm format provides a narrower panel for temporary routes, equipment access, maintenance paths, and locations where the complete 1220 mm width is unnecessary.
The 610 × 2440 mm format may be used for narrow access routes, controlled tire paths, pedestrian access, and restricted working areas.
The 910 × 1830 mm panel provides a compact configuration where transportation, handling, or available installation space is limited.
The 610 × 1830 mm size is suitable for compact temporary access applications and narrow protected routes.
The 610 × 1220 mm panel provides a smaller modular format for restricted areas, pedestrian routes, and local temporary surface protection.
Other listed extruded dimensions include:
These additional dimensions provide more flexibility when planning route width, installation layout, protected working areas, and temporary access systems.
The listed extruded panel thicknesses are:
The correct thickness should be selected according to traffic type, supporting ground, axle loading, tire contact pressure, traffic frequency, installation duration, and route layout.
A thicker panel can provide a more substantial structure, but thickness should not be treated as the only factor affecting performance.
Other important factors include:
The product range also includes larger molded road mats for more demanding temporary access requirements.
Reference molded sizes include:
The large 4500 × 2000 mm format provides approximately 9 square metres of gross panel area before allowing for any connection or installation arrangement.
The 3000 × 1500 mm configuration provides a broad temporary access surface suitable for larger vehicle routes and protected working areas.
The 2000 × 1000 mm and 2300 × 1200 mm formats provide more compact alternatives where very large panels are unnecessary or difficult to transport.
Anti Slip Plastic Ground Protection Mats are available in HDPE and UHMWPE according to the required panel configuration and operating environment.
High-density polyethylene is widely used for outdoor access panels because it can provide:
Ultra-high molecular weight polyethylene can provide additional characteristics such as:
The material should be selected according to the final application, expected traffic, supporting ground, required panel dimensions, selected thickness, and operating environment.
Explore our ground protection mat solutions for related temporary access products and industrial plastic materials.
The upper surface of Anti Slip Plastic Ground Protection Mats features a raised traction structure designed to provide a more defined contact area for vehicle tires and footwear.
The referenced cleat height is approximately 7 mm.
The raised pattern is useful for temporary access across:
The orange mats shown in the product image feature a highly visible raised diamond-style traction surface. Other product configurations may be produced in black, dark green, or other colors according to the selected specification.
Actual traction performance can still be affected by mud accumulation, oil, snow, ice, steep slopes, tire condition, vehicle speed, and weather.
The panel surface should therefore be inspected and cleaned when required.
The product information indicates that the panel can be produced with patterns on both sides or with one patterned surface and one smoother side.
A double-sided patterned panel can provide additional contact with both the vehicle tires above and the supporting surface below.
A panel with a textured upper surface and smoother lower side may be suitable where a different contact arrangement is preferred.
The most suitable surface configuration should be selected according to:
The product range includes compact panels, 4 × 8 ft formats, narrow access mats, and large molded road panels up to approximately 4500 × 2000 mm.
Different polyethylene materials can be selected according to impact resistance, wear requirements, panel structure, and operating conditions.
The referenced cleat height of approximately 7 mm creates a more defined contact surface for temporary vehicle and pedestrian movement.
Extruded mats are available in thicknesses from approximately 12.7 to 20 mm, while larger molded road mats are available in selected configurations from approximately 30 to 100 mm.
The panels can be removed, cleaned, inspected, transported, stored, and installed again depending on their condition.
HDPE and UHMWPE absorb very little moisture compared with temporary timber boards, making them suitable for wet and muddy outdoor environments.
The mats can be used for vehicle access, equipment movement, temporary roadways, landscaping, maintenance routes, outdoor events, and sensitive surface protection.
Anti Slip Plastic Ground Protection Mats can be installed to create temporary vehicle routes across muddy surfaces where direct traffic may cause deep rutting or difficult access conditions.
Repeated vehicle movement directly over mud may cause:
The panels provide a temporary separation layer between the vehicle tires and the original supporting ground.
The effectiveness of the route depends on panel material, size, thickness, ground condition, vehicle type, traffic frequency, and installation quality.
The panels can also be used across grass and soft ground where repeated traffic may cause rutting or surface damage.
Typical applications include:
The mats create a temporary protective layer between traffic and the original ground.
After the access operation is completed, the panels can be removed instead of leaving permanent roadway materials in place.
Anti Slip Plastic Ground Protection Mats can provide temporary equipment access where permanent road construction is unnecessary.
The planned route should consider:
Larger molded panels may be evaluated for more demanding access requirements, while thinner extruded formats may be suitable for lighter temporary access and surface protection.
Multiple panels can be arranged to form:
Panels can be installed in sequence for longer access routes or arranged side by side for wider working areas.
The required layout depends on vehicle width, traffic direction, turning movement, supporting ground, and available installation space.
The product shown includes integrated hand holes designed to assist with panel movement and positioning.
These openings can support:
Appropriate handling procedures should always be used according to the actual panel dimensions and weight.
Large molded panels may require suitable mechanical handling equipment during transportation, placement, and removal.
The supplied product information lists black and dark green as standard colors, with other colors available according to production requirements.
The orange panels shown demonstrate how a brighter color can provide a highly visible temporary access surface.
Different colors may be useful for:
Final color availability should be confirmed according to material, dimensions, panel thickness, and production requirements.
The performance of Anti Slip Plastic Ground Protection Mats depends significantly on the supporting surface beneath each panel.
Before installation:
Sharp objects can create concentrated pressure beneath the panel. Large unsupported areas may reduce effective load distribution.
Better support across the full panel surface generally improves route stability and overall performance.
Position the first mat according to the planned direction of traffic.
Install additional panels in sequence until the required route length has been achieved.
Where a wider access lane or protected working surface is required, arrange additional mats side by side.
Before allowing traffic onto the completed route, inspect:
The temporary route should also be inspected during use, particularly after repeated traffic, heavy rain, or significant changes in supporting ground conditions.
The correct panel should be selected according to actual operating conditions rather than only total vehicle weight.
Important selection factors include:
For lighter temporary access, an extruded 12.7 mm, 15 mm, 18 mm, or 20 mm panel may be considered according to actual conditions.
For large-format temporary road systems, molded panels with thicknesses from approximately 30 mm to 100 mm may be evaluated according to the selected panel size and operating environment.
After outdoor use, excessive mud and debris should be removed when necessary.
Common cleaning methods may include:
Before reuse, inspect each panel for:
The mats should be stacked on stable supporting surfaces and stored in an organized manner.
Anti Slip Plastic Ground Protection Mats combine HDPE and UHMWPE material options, multiple extruded and molded dimensions, thicknesses from 12.7 mm to approximately 100 mm, raised traction structures, integrated handling holes, low moisture absorption, and reusable outdoor performance.
Available extruded dimensions range from compact 610 × 1220 mm panels to large 1220 × 2440 mm formats, while molded road mats include panel sizes up to approximately 4500 × 2000 mm.
The product can be used for temporary vehicle access, muddy roads, soft ground, landscaping, equipment movement, temporary roads, protected working areas, outdoor activities, and other ground protection applications.
Compared with temporary plywood, polyethylene mats do not absorb water, rot, or splinter in the same way. Compared with untreated steel road plates, the plastic material does not rust.
For general information about recognized plastic material and performance testing methods, refer to ASTM International.
With correct panel selection, suitable ground preparation, appropriate installation, regular inspection, and proper handling, Anti Slip Plastic Ground Protection Mats provide a practical and reusable solution for temporary access and outdoor surface protection.
Check drawings for full specifications and confirm materials according to service conditions to prevent product defects.
Inspect all key processing steps and fully verify dimensions, holes, grooves and fitting surfaces.
Deburr, chamfer and clean products for easy installation. Ensure uniform quality among batch products.
Choose appropriate packaging solutions based on product features to protect goods from collision, deformation and mixing during transit.
Unlike metal parts, engineering plastic components still require strict control over dimensions, holes, edges, surface, materials and assembly performance for equipment use.
Engineering plastic parts suit friction, guide, support, buffer, anti-corrosion and insulation areas. We supply UHMWPE, POM, PA, PP/PE components for conveyor, food, mining, machinery, chemical and cable systems, with custom OEM service available.
Stay updated with our latest industry insights, company updates and featured articles.
Engineering plastics are increasingly used in industrial machinery, automated production lines, conveyor systems, packaging equipment, and food-processing machines. Materials such as nylon, UHMWPE, POM, and
Both are lightweight, corrosion-resistant, wear-resistant, and suitable for CNC machining. However, they perform very differently
Wear is a common cause of failure in conveyor systems, packaging machinery, automated equipment, mining
CNC machining is widely used to produce plastic prototypes, low-volume parts, replacement components, jigs, fixtures,
Both are lightweight, corrosion-resistant, wear-resistant, and suitable for CNC machining. However, they perform very differently
Wear is a common cause of failure in conveyor systems, packaging machinery, automated equipment, mining
CNC machining is widely used to produce plastic prototypes, low-volume parts, replacement components, jigs, fixtures,
Need UHMWPE sheets & custom plastic machined/OEM parts？Send specs & material needs, free quote within 24h.
